;0x1200 Modbus通用测试用
[comm]
debug=1  ;打开调试输出信息 默认0（不打开）
delay=50  ;采集指令延时，单位 ms 默认10
mask=0   ;保留
model=OM-MDBS4840       ;型号 添加支持类型用
note=温湿度;  协议说明  
brief=回风温度: %20% ℃,回风湿度: %21% % ;                                                                                                                                                                                                                                                                                                                                                , 温度: %2% % ;简报 %x%为某字段值 简报中不能带分号;

[regs1]
19=12;
127=6;



[regs3];
175=6;
703=3;


[flds]
cnt=21
1=00129;
2=00130;
3=00132;
4=00133;
5=00134;
6=00021;
7=00022;
8=00023;
9=00024;
10=00025;
11=00026;
12=00027;
13=00028;
14=00029;
15=00030;
16=00031;
17=00032;
18=40177;
19=40181;
20=40705;回风温度
21=40706;回风湿度



[flds.def]
;x=FldName,FldDept,Note,vkind,vfactor,vmode,vref,vtip,vref2,vtip2
1='Fld',1,'风机',0,1,0,0,'0:关，1:开',0,''
2='Fld',1,'压缩机',0,1,0,0,'0:关，1:开',0,''
3='Fld',1,'电加热',0,1,0,0,'0:关，1:开',0,''
4='Fld',1,'水泵',0,1,0,0,'0:关，1:开',0,''
5='Fld',1,'故障',0,1,0,0,'0:关，1:开',0,''
6='Fld',1,'电加热保护',0,1,0,0,'0:正常，1:告警',0,''
7='Fld',1,'水浸告警',0,1,0,0,'0:正常，1:告警',0,''
8='Fld',1,'回风低温告警',0,1,0,0,'0:正常，1:告警',0,''
9='Fld',1,'回风高温告警',0,1,0,0,'0:正常，1:告警',0,''
10='Fld',1,'回风高湿告警',0,1,0,0,'0:正常，1:告警',0,''
11='Fld',1,'回风低湿告警',0,1,0,0,'0:正常，1:告警',0,''
12='Fld',1,'送风高温告警',0,1,0,0,'0:正常，1:告警',0,''
13='Fld',1,'送风低温告警',0,1,0,0,'0:正常，1:告警',0,''
14='Fld',1,'高压告警',0,1,0,0,'0:正常，1:告警',0,''
15='Fld',1,'低压告警',0,1,0,0,'0:正常，1:告警',0,''
16='Fld',1,'低过热度报警',0,1,1,25,0,1,0,0,'0:正常，1:告警',0,''
17='Fld',1,'排气高温报警',0,1,1,25,0,1,0,0,'0:正常，1:告警',0,''

20='Fld',1,'回风温度',0,10,11,25,'最小值|允许最低值',35,'最大值|允许最高值'
21='Fld',1,'回风湿度',0,10,11,25,'最小值|允许最低值',35,'最大值|允许最高值'